HTS 7228
Other bars and rods of other alloy steel; angles, shapes and sections, of other alloy steel; hollow drill bars and rods, of alloy or nonalloy steel
| General rate | Not stated for this line What most imports pay — countries with normal trade relations, which is nearly all of them. |
|---|---|
| Special rate | Not stated for this line Only under a trade programme or agreement, and only if the goods qualify. The codes name the programmes. |
| Column 2 rate | Not stated for this line Only for the few countries without normal trade relations. |
This line states no general duty rate, and none is inherited from the lines above it. That is not the same as duty-free: lines in Chapters 98 and 99 are provisions and qualifiers rather than ordinary commodities, and a rate may be stated elsewhere. Check the heading before assuming anything.
Additional duties may apply
This line references Chapter 99, where Section 301, Section 232 and other additional duties live. Those are charged on top of the general rate above and depend on where the goods were made. The rate shown here is therefore not the whole story for every origin.
Statistical breakouts
The 10-digit lines under this code. They are reporting categories; the duty is the one above unless a line states its own.
| Code | Description | Units | Rate |
|---|---|---|---|
| 7228.10.00 | Bars and rods, of high-speed steel | — | Free |
| 7228.10.00.10 | Not cold-formed | kg | Free |
| 7228.10.00.30 | With a maximum cross-sectional dimension of less than 18 mm | kg | Free |
| 7228.10.00.60 | With a maximum cross-sectional dimension of 18 mm or more | kg | Free |
| 7228.20 | Bars and rods, of silico-manganese steel | — | see above |
| 7228.20.10.00 | Not cold-formed | kg | Free |
| 7228.20.50.00 | Cold-formed | kg | Free |
| 7228.30 | Of tool steel (other than high-speed steel) | — | see above |
| 7228.30.20.00 | Of ball-bearing steel | kg | Free |
| 7228.30.40.00 | Of chipper knife steel, not cold-formed | kg | Free |
| 7228.30.60.00 | Other | kg | Free |
| 7228.30.80 | Other | — | Free |
| 7228.30.80.05 | Of high-nickel alloy steel | kg | Free |
| 7228.30.80.10 | Concrete reinforcing bars and rods | kg | Free |
| 7228.30.80.15 | With a diameter or cross section measuring less than 76 mm | kg | Free |
| 7228.30.80.41 | With a diameter or cross section measuring 76 mm or more but not exceeding 152 mm | kg | Free |
| 7228.30.80.45 | With a diameter or cross section measuring 152 mm or more but not exceeding 228 mm | kg | Free |
| 7228.30.80.70 | With a diameter or cross section exceeding 228 mm | kg | Free |
| 7228.40.00.00 | Other bars and rods, not further worked than forged | kg | Free |
| 7228.50 | Other bars and rods, not further worked than cold-formed or cold-finished | — | see above |
| 7228.50.10 | Of tool steel (other than high-speed steel) | — | Free |
| 7228.50.10.10 | Of ball-bearing steel | kg | Free |
| 7228.50.10.20 | Of round or rectangular cross section with surfaces ground, milled or polished | kg | Free |
| 7228.50.10.40 | Other | kg | Free |
| 7228.50.10.60 | Of round or rectangular cross section with surfaces ground, milled or polished | kg | Free |
| 7228.50.10.80 | Other | kg | Free |
| 7228.50.50 | Other | — | Free |
| 7228.50.50.05 | Of high-nickel alloy steel | kg | Free |
| 7228.50.50.15 | With a diameter or cross section measuring less than 76 mm | kg | Free |
| 7228.50.50.40 | With a diameter or cross section measuring 76 mm or more but not exceeding 228 mm | kg | Free |
| 7228.50.50.70 | With a diameter or cross section exceeding 228 mm | kg | Free |
| 7228.60 | Other bars and rods | — | see above |
| 7228.60.10 | Of tool steel (other than high-speed steel) | — | Free |
| 7228.60.10.30 | Of ball-bearing steel | kg | Free |
| 7228.60.10.60 | Other | kg | Free |
| 7228.60.60.00 | Not cold-formed | kg | Free |
| 7228.60.80.00 | Cold-formed | kg | Free |
| 7228.70 | Angles, shapes and sections | — | see above |
| 7228.70.30 | Hot-rolled, not drilled, not punched and not otherwise advanced | — | Free |
| 7228.70.30.10 | U, I, H and T sections | kg | Free |
| 7228.70.30.20 | Angles | kg | Free |
| 7228.70.30.41 | Other | kg | Free |
| 7228.70.30.60 | Angles | kg | Free |
| 7228.70.30.81 | Other | kg | Free |
| 7228.70.60.00 | Other | kg | Free |
| 7228.80.00.00 | Hollow drill bars and rods | kg | Free |
What changed
No recorded change to this line since we began reading the schedule daily. That is the ordinary state: USITC revises it fifteen to eighteen times a year, and most codes are untouched in any given revision.
Email me when this code changes
One email if the duty on 7228 moves, or the line is reworded or withdrawn. USITC publishes revisions without a calendar, and a rate change applies to goods entered from the day it takes effect.
Before you rely on this
Classification and the duties that finally apply to a shipment are a licensed customs broker's call. This page publishes the schedule as USITC does; it does not calculate what an entry will cost.
Source: Harmonized Tariff Schedule of the United States, U.S. International Trade Commission (public domain). Re-checked daily.