HTS 8465
Machine tools (including machines for nailing, stapling, glueing or otherwise assembling) for working wood, cork, bone, hard rubber, hard plastics or similar hard materials
| General rate | Not stated for this line What most imports pay — countries with normal trade relations, which is nearly all of them. |
|---|---|
| Special rate | Not stated for this line Only under a trade programme or agreement, and only if the goods qualify. The codes name the programmes. |
| Column 2 rate | Not stated for this line Only for the few countries without normal trade relations. |
This line states no general duty rate, and none is inherited from the lines above it. That is not the same as duty-free: lines in Chapters 98 and 99 are provisions and qualifiers rather than ordinary commodities, and a rate may be stated elsewhere. Check the heading before assuming anything.
Additional duties may apply
This line references Chapter 99, where Section 301, Section 232 and other additional duties live. Those are charged on top of the general rate above and depend on where the goods were made. The rate shown here is therefore not the whole story for every origin.
Statistical breakouts
The 10-digit lines under this code. They are reporting categories; the duty is the one above unless a line states its own.
| Code | Description | Units | Rate |
|---|---|---|---|
| 8465.10.00 | Machines which can carry out different types of machining operations without tool change between such operations | — | 2.4% |
| 8465.10.00.05 | Tenoners | No. | 2.4% |
| 8465.10.00.15 | Other | No. | 2.4% |
| 8465.10.00.25 | Numerically controlled | No. | 2.4% |
| 8465.10.00.35 | Other | No. | 2.4% |
| 8465.10.00.45 | Other | No. | 2.4% |
| 8465.10.00.50 | Other | No. | 2.4% |
| 8465.20 | Machining centers | — | see above |
| 8465.20.10.00 | For sawing, planing, milling, molding, grinding, sanding, polishing, drilling or mortising | No. | 3% |
| 8465.20.50.00 | For bending or assembling | No. | 2.9% |
| 8465.20.80.00 | Other | No. | 2.4% |
| 8465.91.00 | Sawing machines | — | 3% |
| 8465.91.00.02 | Rip saws | No. | 3% |
| 8465.91.00.06 | Panel saws | No. | 3% |
| 8465.91.00.12 | Band saws | No. | 3% |
| 8465.91.00.16 | Cross-cut and optimizing saws | No. | 3% |
| 8465.91.00.22 | Other | No. | 3% |
| 8465.91.00.27 | Sawmill machines | No. | 3% |
| 8465.91.00.32 | Radial arm saws | No. | 3% |
| 8465.91.00.36 | Tilting arbor table saws | No. | 3% |
| 8465.91.00.41 | Rip saws | No. | 3% |
| 8465.91.00.47 | Miter saws | No. | 3% |
| 8465.91.00.49 | Scroll saws | No. | 3% |
| 8465.91.00.53 | Valued under $3,000 each | No. | 3% |
| 8465.91.00.58 | Other | No. | 3% |
| 8465.91.00.64 | Valued under $1,000 each | No. | 3% |
| 8465.91.00.68 | Other | No. | 3% |
| 8465.91.00.74 | Cross-cut and optimizing saws | No. | 3% |
| 8465.91.00.78 | Other | No. | 3% |
| 8465.91.00.91 | Other | No. | 3% |
| 8465.92.00 | Planing, milling or molding (by cutting) machines | — | 3% |
| 8465.92.00.03 | Moulders | No. | 3% |
| 8465.92.00.06 | Routers | No. | 3% |
| 8465.92.00.16 | Other | No. | 3% |
| 8465.92.00.26 | Valued under $3,000 each | No. | 3% |
| 8465.92.00.29 | Other | No. | 3% |
| 8465.92.00.31 | Moulders | No. | 3% |
| 8465.92.00.34 | Valued under $1,000 each | No. | 3% |
| 8465.92.00.37 | Other | No. | 3% |
| 8465.92.00.42 | Valued under $1,000 each | No. | 3% |
| 8465.92.00.46 | Other | No. | 3% |
| 8465.92.00.51 | Valued under $3,000 each | No. | 3% |
| 8465.92.00.55 | Numerically controlled | No. | 3% |
| 8465.92.00.58 | Other | No. | 3% |
| 8465.92.00.62 | Valued under $1,000 each | No. | 3% |
| 8465.92.00.66 | Other | No. | 3% |
| 8465.92.00.72 | Other | No. | 3% |
| 8465.92.00.91 | Other | No. | 3% |
| 8465.93.00 | Grinding, sanding or polishing machines | — | 3% |
| 8465.93.00.04 | Belt sanders, for a belt width 60 cm or wider | No. | 3% |
| 8465.93.00.12 | Other | No. | 3% |
| 8465.93.00.30 | Valued under $1,000 each | No. | 3% |
| 8465.93.00.45 | Valued $1,000 or over but under $3,000 each | No. | 3% |
| 8465.93.00.55 | Other | No. | 3% |
| 8465.93.00.65 | Belt sanders, for a belt width 60 cm or wider | No. | 3% |
| 8465.93.00.75 | Other | No. | 3% |
| 8465.93.00.91 | Other | No. | 3% |
| 8465.94.00 | Bending or assembling machines | — | 2.9% |
| 8465.94.00.05 | Used or rebuilt | No. | 2.9% |
| 8465.94.00.15 | Doweling machines | No. | 2.9% |
| 8465.94.00.25 | Edgebanding machines | No. | 2.9% |
| 8465.94.00.35 | Laminating machines | No. | 2.9% |
| 8465.94.00.45 | Cold | No. | 2.9% |
| 8465.94.00.55 | Other | No. | 2.9% |
| 8465.94.00.65 | Other | No. | 2.9% |
| 8465.94.00.91 | Other | No. | 2.9% |
| 8465.95.00 | Drilling or mortising machines | — | 3% |
| 8465.95.00.05 | Numerically controlled boring machines | No. | 3% |
| 8465.95.00.10 | Other | No. | 3% |
| 8465.95.00.20 | Numerically controlled | No. | 3% |
| 8465.95.00.35 | Valued under $3,000 each | No. | 3% |
| 8465.95.00.45 | Other | No. | 3% |
| 8465.95.00.55 | Valued under $1,000 each | No. | 3% |
| 8465.95.00.60 | Other | No. | 3% |
| 8465.95.00.65 | Other | No. | 3% |
| 8465.95.00.91 | Other | No. | 3% |
| 8465.96.00 | Splitting, slicing or paring machines | — | 2.4% |
| 8465.96.00.15 | Log splitters | No. | 2.4% |
| 8465.96.00.25 | Chippers | No. | 2.4% |
| 8465.96.00.30 | Hogs | No. | 2.4% |
| 8465.96.00.40 | Other | No. | 2.4% |
| 8465.96.00.51 | Other | No. | 2.4% |
| 8465.99.02 | Other | — | 2.4% |
| 8465.99.02.10 | Debarkers | No. | 2.4% |
| 8465.99.02.20 | Lathes | No. | 2.4% |
| 8465.99.02.30 | Other | No. | 2.4% |
| 8465.99.02.50 | Other | No. | 2.4% |
What changed
No recorded change to this line since we began reading the schedule daily. That is the ordinary state: USITC revises it fifteen to eighteen times a year, and most codes are untouched in any given revision.
Email me when this code changes
One email if the duty on 8465 moves, or the line is reworded or withdrawn. USITC publishes revisions without a calendar, and a rate change applies to goods entered from the day it takes effect.
Before you rely on this
Classification and the duties that finally apply to a shipment are a licensed customs broker's call. This page publishes the schedule as USITC does; it does not calculate what an entry will cost.
Source: Harmonized Tariff Schedule of the United States, U.S. International Trade Commission (public domain). Re-checked daily.