HTS 7317.00
Nails, tacks, drawing pins, corrugated nails, staples (other than those of heading 8305) and similar articles, of iron or steel, whether or not with heads of other material, but excluding such articles with heads of copper
| General rate | Not stated for this line What most imports pay — countries with normal trade relations, which is nearly all of them. |
|---|---|
| Special rate | Not stated for this line Only under a trade programme or agreement, and only if the goods qualify. The codes name the programmes. |
| Column 2 rate | Not stated for this line Only for the few countries without normal trade relations. |
This line states no general duty rate, and none is inherited from the lines above it. That is not the same as duty-free: lines in Chapters 98 and 99 are provisions and qualifiers rather than ordinary commodities, and a rate may be stated elsewhere. Check the heading before assuming anything.
Additional duties may apply
This line references Chapter 99, where Section 301, Section 232 and other additional duties live. Those are charged on top of the general rate above and depend on where the goods were made. The rate shown here is therefore not the whole story for every origin.
Statistical breakouts
The 10-digit lines under this code. They are reporting categories; the duty is the one above unless a line states its own.
| Code | Description | Units | Rate |
|---|---|---|---|
| 7317.00.10.00 | Thumb tacks | kg | Free |
| 7317.00.20.00 | Not threaded | kg | Free |
| 7317.00.30.00 | Threaded | kg | Free |
| 7317.00.55 | Made of round wire | — | Free |
| 7317.00.55.01 | Collated roofing nails with a length of 20.6 mm to 46.1 mm, a head diameter of 8.3 mm to 10.6 mm, a shank diameter of 2.5 mm to 3.2 mm, whether or not galvanized | kg | Free |
| 7317.00.55.02 | Galvanized | kg | Free |
| 7317.00.55.03 | Other | kg | Free |
| 7317.00.55.05 | Galvanized | kg | Free |
| 7317.00.55.07 | Other | kg | Free |
| 7317.00.55.08 | Assembled in a paper strip | kg | Free |
| 7317.00.55.11 | Assembled in a wire strip | kg | Free |
| 7317.00.55.18 | Other | kg | Free |
| 7317.00.55.19 | With a length of less than 25.4 mm and with a diameter of less than 1.65 mm | kg | Free |
| 7317.00.55.20 | Not coated, plated or painted | kg | Free |
| 7317.00.55.30 | Galvanized | kg | Free |
| 7317.00.55.40 | Vinyl, resin or cement coated | kg | Free |
| 7317.00.55.50 | Other | kg | Free |
| 7317.00.55.60 | Not coated, plated or painted | kg | Free |
| 7317.00.55.70 | Galvanized | kg | Free |
| 7317.00.55.80 | Vinyl, resin or cement coated | kg | Free |
| 7317.00.55.90 | Other | kg | Free |
| 7317.00.65 | Other | — | Free |
| 7317.00.65.30 | Cut | kg | Free |
| 7317.00.65.60 | Other | kg | Free |
| 7317.00.75.00 | Of two or more pieces | kg | Free |
What changed
No recorded change to this line since we began reading the schedule daily. That is the ordinary state: USITC revises it fifteen to eighteen times a year, and most codes are untouched in any given revision.
Email me when this code changes
One email if the duty on 7317.00 moves, or the line is reworded or withdrawn. USITC publishes revisions without a calendar, and a rate change applies to goods entered from the day it takes effect.
Before you rely on this
Classification and the duties that finally apply to a shipment are a licensed customs broker's call. This page publishes the schedule as USITC does; it does not calculate what an entry will cost.
Source: Harmonized Tariff Schedule of the United States, U.S. International Trade Commission (public domain). Re-checked daily.